As an Amazon Associate I earn from qualifying purchases.
1. QWinOut #ad
QWinOut APM 2.8 Multicopter Flight Controller Board with Case Compass & Extension Cable for FPV RC Drone Multirotor DIY Quadcopter #adQWinOut #ad
- Includes 3-axis gyro, accelerometer and Magnetometer, Along with a High-performance Barometer. Apm is an open source flight control, Can You Play APM Well Depend On Individual Ability.
With protective case but No Shock Absorber! Package included: 1* apm2. 8 flight controller build-in compass with protective Case 5* 10cm Extension Lead Wire Cable Male To Male 1* 6m GPS with Compass l5883 25cm Cable.
Player must have ability of basic understanding of monolithic integrated Circuit, Mechanical, c-Language, Knowledge of Electrical, Financial and Material Resources, and Also Needs a Certain Degree Of Mental Capacity, Energy Support.
2. FPVDrone #ad
APM2.6 Flight Controller Board with Top-Pin Connector for ArduPilot Mega 2.6 Flight Control Board #adFPVDrone #ad
- Atmel's atmega2560 and atmega32u-2 chips for processing and usb functions respectively. 6 autopilot module, but does not have an onboard compass, which makes this version ideal for use with multicopters and rovers. This is the new apm 2.
Barometric pressure sensor upgraded to MS5611-01BA03, accelerometer and magnetometer, from Measurement Specialties. One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000 We have m8n gps for this flight controller, ASIN: B06XR6JHDW. Includes 3-axis gyro, along with a high-performance barometer.
3. YoungRC #ad
YoungRC APM2.8 Flight Controller Board Built in Compass Straight Pin for RC F450 S500 Quadcopter Drone #adYoungRC #ad
- Modified version added isolation resistor, when the OSD interface used with telemetry, the interfaces is effectively avoided. Put df13-5p gps interface with external compass interface, convenient for the connection of GPS and external compass.
The new version adopts us lp2985-3. 3, more reliable, 16v withstand voltage, redcucing the possibility of Bad Gyro health. This version eliminates the 1. 0mm 6p sm06b gps interface of V2. 52 old version, change it into DF13-4P I2C external compass interface. V2. 52 i2c interface changes to multifunctional MUX interface.
4. Readytosky #ad
Readytosky Pixhawk PX4 Flight Controller PIX 2.4.8 32 Bit Flight Control Board+Safety Switch+Buzzer+I2C Splitter Expand Module+16GB SD Card #adReadytosky #ad
- If you have problems with using it, please check these videos: https://www. Youtube. Com/watch?v=uh2icra9g7k&t=1187s https://www. Youtube. Com/watch?v=cfq-9MIHKkU&t=19s. And the 3dr radio telemetry kit for this flight controller, ASIN: B01DHV4DVA.
The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. We have m8n gps for the pixhawk flight controller, ASIN : B01KK9A8QG. The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;.
5. FPVDrone #ad
FPVDrone 8CH PPM Encoder&Pixhawk I2C Splitter Expand Module for Pixhawk Flight Controller APM Flight Controller #adFPVDrone #ad
- In case you would like to change the settings of the PPM encoder to invert the PPM signal and change the fail safe pre-defined values you will need an AVR ISP programmer in order to reprogram it.
Expands the i2c port to allow up to four additional peripherals to connect to pixhawk. Use the 4-wire cable to connect the i2c splitter and add a compass module, external led, digital airspeed sensor, or other peripherals to your vehicle.
Pixhawk. The design of the ppm encoder is based on the Paperazzi PPM Encoder. Important note:the firmware comes pre-configured to read 8 channels.
The ppm encoder plugs into the pwm servo output ports of any R/C receiver and encodes them into a PPM pulse suitable for many autopilots e. G. Modifications to the R/C receiver are not necessary. The whole project is based around the atmeL ATMEGA328p AVR processor and all timing is done within interrupts so accuracy and stability is optimized.
6. iFlight #ad
IFlight SucceX-D F7 TwinG Dual ICM20689 Flight Controller F7 FC Built-in OSD BEC Current Sensor Black Box for DJI FPV Air Unit HD Version #adiFlight #ad
- F7 fc included a connector specifically for DJI air unit, so installation should be a breeze. Built-in osd, optimized circuit design, 9v/2.
5a bec, double 5V/2. 5a, high-performance hardware, further guarantees powerful performance of flight controller. Fc board add the popular and reliable USB Type-C instead of Micro USB which makes connection easily.
The f7 flight controller hd version is designed to work seamlessly for DJI’s new HD FPV system. This flight controller is ready for anything with 5 uarts, 8 motor outputs, Dual ICM20689 gyro, 32mb blackbox and a powerful F7 processor to run it all.
7. Hobbypower #ad
Hobbypower APM2.8 Flight Controller 7M GPS 3DR 915Mhz Telemetry Mini OSD Module Power Module for FPV Quadcopter Multirotor #adHobbypower #ad
- Newest apm version, with Shock Absorber designed. Package includes: 1x apm2. 8 flight controller with shock absorber, 1x 7m gps module, 1x mini oSD Module, 1x power module, 1x 3DR 915Mhz Radio Wireless Telemetry set, 1x GPS bracket.
8. FPVDrone #ad
FPVDrone Power Module V1.0 XT60 Plug Current Sensor for APM2.8 APM2.6 APM Pixhawk Flight Controller #adFPVDrone #ad
- Voltage and current measurement configured for 5V ADC. Use your aircraft's own ESC/BEC for that. The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection.
It isnotdesigned to power servos. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. Switching regulator outputs 5. 3v and 3A max. 6-pos df13 cable plugs directly to APM 2. 5's 'pm' connector.
9. Hobbypower #ad
Hobbypower Power Module V1.0 with XT60 Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller #adHobbypower #ad
- Another signal cable connectors are used in Japan original fittings, you can output 5. 3 dc, non-domestic joint, so APM flight control board and reliable connection between the power supply module.
The on-board switching regulator outputs 5. 3v and a maximum of 2. 25a from up to a 4S LiPo battery. In addition the module also comes with bec function, 3a maximum continuous current for the flight control board to provide a stable power supply.
The apm power module is a simple way of providing your apm fc with clean power from a lipo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable.
Used to detect the battery voltage and the battery current, calculate the remaining battery power, flight control board receives two signals, estimate the remaining flight time. The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection.